nxos_igmp_interface - Manages IGMP interface configuration.

New in version 2.2.

Synopsis
Parameters
Notes
Examples
Return Values
Status
- Support
- Author

Synopsis

Manages IGMP interface configuration settings.

Parameters

Parameter		Choices/Defaults	Comments
group_timeout		Default: None	Sets the group membership timeout for IGMPv2. Values can range from 3 to 65,535 seconds. The default is 260 seconds.
immediate_leave		Choices: true false Default: no	Enables the device to remove the group entry from the multicast routing table immediately upon receiving a leave message for the group. Use this command to minimize the leave latency of IGMPv2 group memberships on a given IGMP interface because the device does not send group-specific queries. The default is disabled.
interface required			The full interface name for IGMP configuration. e.g. Ethernet1/2.
last_member_qrt		Default: None	Sets the query interval waited after sending membership reports before the software deletes the group state. Values can range from 1 to 25 seconds. The default is 1 second.
last_member_query_count		Default: None	Sets the number of times that the software sends an IGMP query in response to a host leave message. Values can range from 1 to 5. The default is 2.
oif_prefix		Default: None	Configure a prefix for static outgoing interface (OIF).
oif_routemap		Default: None	Configure a routemap for static outgoing interface (OIF).
oif_source		Default: None	Configure a source for static outgoing interface (OIF).
provider		Default: None	Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli`. This option is only required if you are using NX-API. For more information please see the NXOS Platform Options guide. A dict object containing connection details.
	username		Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate either the CLI login or the nxapi authentication depending on which transport is used. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
	authorize (added in 2.5.3)	Choices: no ← yes	Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTHORIZE` will be used instead.
	ssh_keyfile		Specifies the SSH key to use to authenticate the connection to the remote device. This argument is only used for the cli transport. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
	use_proxy (added in 2.5)	Choices: yes ← no	If `no`, the environment variables `http_proxy` and `https_proxy` will be ignored.
	auth_pass (added in 2.5.3)	Default: none	Specifies the password to use if required to enter privileged mode on the remote device. If authorize is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTH_PASS` will be used instead.
	host required		Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
	timeout (added in 2.3)	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error. NX-API can be slow to return on long-running commands (sh mac, sh bgp, etc).
	use_ssl	Choices: yes no ←	Configures the transport to use SSL if set to true only when the `transport=nxapi`, otherwise this value is ignored.
	password	Default: None	Specifies the password to use to authenticate the connection to the remote device. This is a common argument used for either cli or nxapi transports. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
	validate_certs	Choices: yes no Default: None	If `no`, SSL certificates will not be validated. This should only be used on personally controlled sites using self-signed certificates. If the transport argument is not nxapi, this value is ignored.
	port	Default: 0 (use common port)	Specifies the port to use when building the connection to the remote device. This value applies to either cli or nxapi. The port value will default to the appropriate transport common port if none is provided in the task. (cli=22, http=80, https=443).
	transport required	Default: cli	Configures the transport connection to use when connecting to the remote device. The transport argument supports connectivity to the device over cli (ssh) or nxapi.
querier_timeout		Default: None	Sets the querier timeout that the software uses when deciding to take over as the querier. Values can range from 1 to 65535 seconds. The default is 255 seconds.
query_interval		Default: None	Sets the frequency at which the software sends IGMP host query messages. Values can range from 1 to 18000 seconds. The default is 125 seconds.
query_mrt		Default: None	Sets the response time advertised in IGMP queries. Values can range from 1 to 25 seconds. The default is 10 seconds.
report_llg		Choices: true false Default: no	Configures report-link-local-groups. Enables sending reports for groups in 224.0.0.0/24. Reports are always sent for nonlink local groups. By default, reports are not sent for link local groups.
restart		Choices: true false Default: None	Restart IGMP.
robustness		Default: None	Sets the robustness variable. Values can range from 1 to 7. The default is 2.
startup_query_count		Default: None	Query count used when the IGMP process starts up. The range is from 1 to 10. The default is 2.
startup_query_interval		Default: None	Query interval used when the IGMP process starts up. The range is from 1 to 18000. The default is 31.
state		Choices: present ← default	Manages desired state of the resource.
version		Choices: 2 3 Default: None	IGMP version. It can be 2 or 3.

Notes

Note

Tested against NXOSv 7.3.(0)D1(1) on VIRL
When state=default, supported params will be reset to a default state. These include version, startup_query_interval, startup_query_count, robustness, querier_timeout, query_mrt, query_interval, last_member_qrt, last_member_query_count, group_timeout, report_llg, and immediate_leave.
When state=absent, all configs for oif_prefix, oif_source, and oif_routemap will be removed.
PIM must be enabled to use this module.
This module is for Layer 3 interfaces.
Route-map check not performed (same as CLI) check when configuring route-map with ‘static-oif’
If restart is set to true with other params set, the restart will happen last, i.e. after the configuration takes place.
For information on using CLI and NX-API see the NXOS Platform Options guide
For more information on using Ansible to manage network devices see the Ansible Network Guide
For more information on using Ansible to manage Cisco devices see the Cisco integration page.

Examples

- nxos_igmp_interface:
    interface: ethernet1/32
    startup_query_interval: 30
    state: present

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
changed boolean	always	check to see if a change was made on the device Sample: True
end_state dict	always	k/v pairs of BGP configuration after module execution Sample: {'router_id': '1.1.1.1', 'neighbor_down_fib_accelerate': False, 'confederation_peers': '', 'confederation_id': '', 'bestpath_compare_neighborid': False, 'local_as': '', 'bestpath_always_compare_med': False, 'bestpath_med_non_deterministic': False, 'cluster_id': '', 'vrf': 'test', 'graceful_restart_helper': False, 'timer_bgp_hold': '180', 'bestpath_aspath_multipath_relax': False, 'asn': '65535', 'timer_bestpath_limit': '', 'graceful_restart_timers_stalepath_time': '300', 'graceful_restart_timers_restart': '120', 'maxas_limit': '', 'bestpath_med_confed': False, 'log_neighbor_changes': False, 'timer_bgp_keepalive': '60', 'bestpath_cost_community_ignore': False, 'reconnect_interval': '60', 'suppress_fib_pending': False, 'bestpath_med_missing_as_worst': False, 'bestpath_compare_routerid': False, 'graceful_restart': True}
existing dict	always	k/v pairs of existing BGP configuration Sample: {'router_id': '11.11.11.11', 'neighbor_down_fib_accelerate': False, 'confederation_peers': '', 'confederation_id': '', 'bestpath_compare_neighborid': False, 'local_as': '', 'bestpath_always_compare_med': False, 'bestpath_med_non_deterministic': False, 'cluster_id': '', 'vrf': 'test', 'graceful_restart_helper': False, 'timer_bgp_hold': '180', 'bestpath_aspath_multipath_relax': False, 'asn': '65535', 'timer_bestpath_limit': '', 'graceful_restart_timers_stalepath_time': '300', 'graceful_restart_timers_restart': '120', 'maxas_limit': '', 'bestpath_med_confed': False, 'log_neighbor_changes': False, 'timer_bgp_keepalive': '60', 'bestpath_cost_community_ignore': False, 'reconnect_interval': '60', 'suppress_fib_pending': False, 'bestpath_med_missing_as_worst': False, 'bestpath_compare_routerid': False, 'graceful_restart': True}
proposed dict	always	k/v pairs of parameters passed into module Sample: {'router_id': '1.1.1.1', 'asn': '65535', 'vrf': 'test'}
updates list	always	commands sent to the device Sample: ['router bgp 65535', 'vrf test', 'router-id 1.1.1.1']

Status

This module is flagged as preview which means that it is not guaranteed to have a backwards compatible interface.

Support

For more information about Red Hat’s support of this module, please refer to this Knowledge Base article

Author

Jason Edelman (@jedelman8)
Gabriele Gerbino (@GGabriele)

Hint

If you notice any issues in this documentation you can edit this document to improve it.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.5/modules/nxos_igmp_interface_module.html