bigip_trunk – Manage trunks on a BIG-IP

New in version 2.6.

Synopsis
Parameters
Notes
Examples
Return Values
Status

Synopsis

Manages trunks on a BIG-IP.

Parameters

Parameter		Choices/Defaults	Comments
description string added in 2.7			Description of the trunk.
frame_distribution_hash string		Choices: destination-mac source-destination-ip source-destination-mac	Specifies the basis for the hash that the system uses as the frame distribution algorithm. The system uses the resulting hash to determine which interface to use for forwarding traffic. When creating a new trunk, if this parameter is not specified, the default is `source-destination-ip`. When `source-destination-mac`, specifies that the system bases the hash on the combined MAC addresses of the source and the destination. When `destination-mac`, specifies that the system bases the hash on the MAC address of the destination. When `source-destination-ip`, specifies that the system bases the hash on the combined IP addresses of the source and the destination.
interfaces list			The interfaces that are part of the trunk. To clear the list of interfaces, specify an empty list.
lacp_enabled boolean		Choices: no yes	When `yes`, specifies that the system supports the link aggregation control protocol (LACP), which monitors the trunk by exchanging control packets over the member links to determine the health of the links. If LACP detects a failure in a member link, it removes the link from the link aggregation. When creating a new trunk, if this parameter is not specified, LACP is `no`. LACP is disabled by default for backward compatibility. If this does not apply to your network, we recommend that you enable LACP.
lacp_mode string		Choices: active passive	Specifies the operation mode for link aggregation control protocol (LACP), if LACP is enabled for the trunk. When creating a new trunk, if this parameter is not specified, the default is `active`. When `active`, specifies that the system periodically sends control packets regardless of whether the partner system has issued a request. When `passive`, specifies that the system sends control packets only when the partner system has issued a request.
lacp_timeout string		Choices: long short	Specifies the rate at which the system sends the LACP control packets. When creating a new trunk, if this parameter is not specified, the default is `long`. When `long`, specifies that the system sends an LACP control packet every 30 seconds. When `short`, specifies that the system sends an LACP control packet every 1 seconds.
link_selection_policy string		Choices: auto maximum-bandwidth	Specifies, once the trunk is configured, the policy that the trunk uses to determine which member link (interface) can handle new traffic. When creating a new trunk, if this value is not specific, the default is `auto`. When `auto`, specifies that the system automatically determines which interfaces can handle new traffic. For the `auto` option, the member links must all be the same media type and speed. When `maximum-bandwidth`, specifies that the system determines which interfaces can handle new traffic based on the members' maximum bandwidth.
name string / required			Specifies the name of the trunk.
password string / required			The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable `F5_PASSWORD`. aliases: pass, pwd
provider dictionary added in 2.5			A dict object containing connection details.
	password string / required		The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable `F5_PASSWORD`. aliases: pass, pwd
	server string / required		The BIG-IP host. You may omit this option by setting the environment variable `F5_SERVER`.
	server_port integer	Default: 443	The BIG-IP server port. You may omit this option by setting the environment variable `F5_SERVER_PORT`.
	ssh_keyfile path		Specifies the SSH keyfile to use to authenticate the connection to the remote device. This argument is only used for cli transports. You may omit this option by setting the environment variable `ANSIBLE_NET_SSH_KEYFILE`.
	timeout integer	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
	transport string	Choices: cli rest ←	Configures the transport connection to use when connecting to the remote device.
	user string / required		The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable `F5_USER`.
	validate_certs boolean	Choices: no yes ←	If `no`, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates. You may omit this option by setting the environment variable `F5_VALIDATE_CERTS`.
qinq_ethertype raw added in 2.7			Specifies the ether-type value used for the packets handled on this trunk when it is a member in a QinQ vlan. The ether-type can be set to any string containing a valid hexadecimal 16 bits number, or any of the well known ether-types; `0x8100`, `0x9100`, `0x88a8`. This parameter is not supported on Virtual Editions. You should always wrap this value in quotes to prevent Ansible from interpreting the value as a literal hexadecimal number and converting it to an integer.
server string / required			The BIG-IP host. You may omit this option by setting the environment variable `F5_SERVER`.
server_port integer added in 2.2		Default: 443	The BIG-IP server port. You may omit this option by setting the environment variable `F5_SERVER_PORT`.
state string		Choices: present ← absent	When `present`, ensures that the resource exists. When `absent`, ensures the resource is removed.
user string / required			The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable `F5_USER`.
validate_certs boolean added in 2.0		Choices: no yes ←	If `no`, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates. You may omit this option by setting the environment variable `F5_VALIDATE_CERTS`.

Notes

Note

For more information on using Ansible to manage F5 Networks devices see https://www.ansible.com/integrations/networks/f5.
Requires BIG-IP software version >= 12.
The F5 modules only manipulate the running configuration of the F5 product. To ensure that BIG-IP specific configuration persists to disk, be sure to include at least one task that uses the bigip_config module to save the running configuration. Refer to the module’s documentation for the correct usage of the module to save your running configuration.

Examples

- name: Create a trunk on hardware
  bigip_trunk:
    name: trunk1
    interfaces:
      - 1.1
      - 1.2
    link_selection_policy: maximum-bandwidth
    frame_distribution_hash: destination-mac
    lacp_enabled: yes
    lacp_mode: passive
    lacp_timeout: short
    provider:
      password: secret
      server: lb.mydomain.com
      user: admin
  delegate_to: localhost

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
description string	changed	Description of the trunk. Sample: My trunk
frame_distribution_hash string	changed	Hash that the system uses as the frame distribution algorithm. Sample: src-dst-ipport
interfaces list	changed	Interfaces that are part of the trunk. Sample: ['int1', 'int2']
lacp_enabled boolean	changed	Whether the system supports the link aggregation control protocol (LACP) or not. Sample: True
lacp_mode string	changed	Operation mode for LACP if the lacp option is enabled for the trunk. Sample: active
lacp_timeout string	changed	Rate at which the system sends the LACP control packets. Sample: long
link_selection_policy string	changed	LACP policy that the trunk uses to determine which member link (interface) can handle new traffic. Sample: auto
qinq_ethertype string	changed	Ether-type value used for the packets handled on this trunk when it is a member in a QinQ vlan. Sample: 37120

Status

This module is not guaranteed to have a backwards compatible interface. [preview]
This module is maintained by an Ansible Partner. [certified]

Authors

Tim Rupp (@caphrim007)
Wojciech Wypior (@wojtek0806)

Hint

If you notice any issues in this documentation you can edit this document to improve it.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.8/modules/bigip_trunk_module.html