cisco.ios.ios_vlans – VLANs resource module
Note
This plugin is part of the cisco.ios collection (version 2.5.0).
You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.
To install it, use: ansible-galaxy collection install cisco.ios.
To use it in a playbook, specify: cisco.ios.ios_vlans.
New in version 1.0.0: of cisco.ios
Synopsis
- This module provides declarative management of VLANs on Cisco IOS network devices.
Note
This module has a corresponding action plugin.
Parameters
| Parameter | Choices/Defaults | Comments | |
|---|---|---|---|
| config list / elements=dictionary | A dictionary of VLANs options | ||
| mtu integer | VLAN Maximum Transmission Unit. Refer to vendor documentation for valid values. | ||
| name string | Ascii name of the VLAN. NOTE, name should not be named/appended with default as it is reserved for device default vlans. | ||
| remote_span boolean |
| Configure as Remote SPAN VLAN | |
| shutdown string |
| Shutdown VLAN switching. | |
| state string |
| Operational state of the VLAN | |
| vlan_id integer / required | ID of the VLAN. Range 1-4094 | ||
| running_config string | This option is used only with state parsed. The value of this option should be the output received from the IOS device by executing the command show vlan. The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module's argspec and the value is then returned in the parsed key within the result. | ||
| state string |
| The state the configuration should be left in The states rendered, gathered and parsed does not perform any change on the device. The state rendered will transform the configuration in config option to platform specific CLI commands which will be returned in the rendered key within the result. For state rendered active connection to remote host is not required.The state gathered will fetch the running configuration from device and transform it into structured data in the format as per the resource module argspec and the value is returned in the gathered key within the result. The state parsed reads the configuration from running_config option and transforms it into JSON format as per the resource module parameters and the value is returned in the parsed key within the result. The value of running_config option should be the same format as the output of command show running-config | include ip route|ipv6 route executed on device. For state parsed active connection to remote host is not required. | |
Notes
Note
- Tested against Cisco IOSl2 device with Version 15.2 on VIRL.
- Starting from v2.5.0, this module will fail when run against Cisco IOS devices that do not support VLANs. The offline states (
renderedandparsed) will work as expected.
Examples
# Using merged
# Before state:
# -------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
- name: Merge provided configuration with device configuration
cisco.ios.ios_vlans:
config:
- name: Vlan_10
vlan_id: 10
state: active
shutdown: disabled
remote_span: true
- name: Vlan_20
vlan_id: 20
mtu: 610
state: active
shutdown: enabled
- name: Vlan_30
vlan_id: 30
state: suspend
shutdown: enabled
state: merged
# After state:
# ------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 vlan_20 act/lshut
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 610 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
#
# Remote SPAN VLANs
# ------------------------------------------------------------------------------
# 10
# Using overridden
# Before state:
# -------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 vlan_20 act/lshut
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 610 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
#
# Remote SPAN VLANs
# ------------------------------------------------------------------------------
# 10
- name: Override device configuration of all VLANs with provided configuration
cisco.ios.ios_vlans:
config:
- name: Vlan_10
vlan_id: 10
mtu: 1000
state: overridden
# After state:
# ------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 Vlan_10 active
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1000 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
# Using replaced
# Before state:
# -------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 vlan_20 act/lshut
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 610 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
#
# Remote SPAN VLANs
# ------------------------------------------------------------------------------
# 10
- name: Replaces device configuration of listed VLANs with provided configuration
cisco.ios.ios_vlans:
config:
- vlan_id: 20
name: Test_VLAN20
mtu: 700
shutdown: disabled
- vlan_id: 30
name: Test_VLAN30
mtu: 1000
state: replaced
# After state:
# ------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 Test_VLAN20 active
# 30 Test_VLAN30 active
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 700 - - - - - 0 0
# 30 enet 100030 1000 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
#
# Remote SPAN VLANs
# ------------------------------------------------------------------------------
# 10
# Using deleted
# Before state:
# -------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 vlan_20 act/lshut
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 610 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
#
# Remote SPAN VLANs
# ------------------------------------------------------------------------------
# 10
- name: Delete attributes of given VLANs
cisco.ios.ios_vlans:
config:
- vlan_id: 10
- vlan_id: 20
state: deleted
# After state:
# -------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
# Using Deleted without any config passed
#"(NOTE: This will delete all of configured vlans attributes)"
# Before state:
# -------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 vlan_20 act/lshut
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 610 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
#
# Remote SPAN VLANs
# ------------------------------------------------------------------------------
# 10
- name: Delete attributes of ALL VLANs
cisco.ios.ios_vlans:
state: deleted
# After state:
# -------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
# Using Gathered
# Before state:
# -------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 vlan_20 act/lshut
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 610 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
#
# Remote SPAN VLANs
# ------------------------------------------------------------------------------
# 10
- name: Gather listed vlans with provided configurations
cisco.ios.ios_vlans:
config:
state: gathered
# Module Execution Result:
# ------------------------
#
# "gathered": [
# {
# "mtu": 1500,
# "name": "default",
# "shutdown": "disabled",
# "state": "active",
# "vlan_id": 1
# },
# {
# "mtu": 1500,
# "name": "VLAN0010",
# "shutdown": "disabled",
# "state": "active",
# "vlan_id": 10
# },
# {
# "mtu": 1500,
# "name": "VLAN0020",
# "shutdown": "disabled",
# "state": "active",
# "vlan_id": 20
# },
# {
# "mtu": 1500,
# "name": "VLAN0030",
# "shutdown": "disabled",
# "state": "active",
# "vlan_id": 30
# },
# {
# "mtu": 1500,
# "name": "fddi-default",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 1002
# },
# {
# "mtu": 1500,
# "name": "token-ring-default",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 1003
# },
# {
# "mtu": 1500,
# "name": "fddinet-default",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 1004
# },
# {
# "mtu": 1500,
# "name": "trnet-default",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 1005
# }
# ]
# After state:
# ------------
#
# vios_l2#show vlan
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 vlan_20 act/lshut
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 610 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
#
# Remote SPAN VLANs
# ------------------------------------------------------------------------------
# 10
# Using Rendered
- name: Render the commands for provided configuration
cisco.ios.ios_vlans:
config:
- name: Vlan_10
vlan_id: 10
state: active
shutdown: disabled
remote_span: true
- name: Vlan_20
vlan_id: 20
mtu: 610
state: active
shutdown: enabled
- name: Vlan_30
vlan_id: 30
state: suspend
shutdown: enabled
state: rendered
# Module Execution Result:
# ------------------------
#
# "rendered": [
# "vlan 10",
# "name Vlan_10",
# "state active",
# "remote-span",
# "no shutdown",
# "vlan 20",
# "name Vlan_20",
# "state active",
# "mtu 610",
# "shutdown",
# "vlan 30",
# "name Vlan_30",
# "state suspend",
# "shutdown"
# ]
# Using Parsed
# File: parsed.cfg
# ----------------
#
# VLAN Name Status Ports
# ---- -------------------------------- --------- -------------------------------
# 1 default active Gi0/1, Gi0/2
# 10 vlan_10 active
# 20 vlan_20 act/lshut
# 30 vlan_30 sus/lshut
# 1002 fddi-default act/unsup
# 1003 token-ring-default act/unsup
# 1004 fddinet-default act/unsup
# 1005 trnet-default act/unsup
#
# VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
# ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
# 1 enet 100001 1500 - - - - - 0 0
# 10 enet 100010 1500 - - - - - 0 0
# 20 enet 100020 1500 - - - - - 0 0
# 30 enet 100030 1500 - - - - - 0 0
# 1002 fddi 101002 1500 - - - - - 0 0
# 1003 tr 101003 1500 - - - - - 0 0
# 1004 fdnet 101004 1500 - - - ieee - 0 0
# 1005 trnet 101005 1500 - - - ibm - 0 0
- name: Parse the commands for provided configuration
cisco.ios.ios_vlans:
running_config: "{{ lookup('file', './parsed.cfg') }}"
state: parsed
# Module Execution Result:
# ------------------------
#
# "parsed": [
# {
# "mtu": 1500,
# "name": "default",
# "shutdown": "disabled",
# "state": "active",
# "vlan_id": 1
# },
# {
# "mtu": 1500,
# "name": "vlan_10",
# "shutdown": "disabled",
# "state": "active",
# "vlan_id": 10
# },
# {
# "mtu": 1500,
# "name": "vlan_20",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 20
# },
# {
# "mtu": 1500,
# "name": "vlan_30",
# "shutdown": "enabled",
# "state": "suspend",
# "vlan_id": 30
# },
# {
# "mtu": 1500,
# "name": "fddi-default",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 1002
# },
# {
# "mtu": 1500,
# "name": "token-ring-default",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 1003
# },
# {
# "mtu": 1500,
# "name": "fddinet-default",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 1004
# },
# {
# "mtu": 1500,
# "name": "trnet-default",
# "shutdown": "enabled",
# "state": "active",
# "vlan_id": 1005
# }
# ]
Return Values
Common return values are documented here, the following are the fields unique to this module:
| Key | Returned | Description |
|---|---|---|
| after list / elements=string | when changed | The configuration as structured data after module completion. Sample: The configuration returned will always be in the same format of the parameters above. |
| before list / elements=string | always | The configuration as structured data prior to module invocation. Sample: The configuration returned will always be in the same format of the parameters above. |
| commands list / elements=string | always | The set of commands pushed to the remote device. Sample: ['vlan 20', 'name vlan_20', 'mtu 600', 'remote-span'] |
Authors
- Sumit Jaiswal (@justjais)
© 2012–2018 Michael DeHaan
© 2018–2021 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/latest/collections/cisco/ios/ios_vlans_module.html